|Shopping cart is empty.|
POWER-GRIP (5 meter)$69.00
***IN STOCK - ORDER YOURS TODAY!***
Pedal Board Tape - Pedalboard Velcro Alternative
For the best Pedalboard Velcro Alternative, try Power-All Power-Grip. Simple, yet ingenious, Power-Grip pedal board tape mates to itself via rows of tiny mushroom-shaped posts that form a much stronger bond than traditional "hook & loop" Velcro fasteners. Just cut to size, apply, and GRIP!
Power-Grip Is Available In The Following Configurations
- 1-Meter Roll (Click to Order) – Single-sided, 1-meter (39.37 inch) long x 1 inch wide roll - approximately enough for 6 standard-sized pedals. $14.95
- 5-Meter Roll (add to cart above) – Single-sided, 5-meter (Approx. 16 feet) x 1inch wide roll – Enough tape to cover PT-JR & still have some tape left over for your pedal backs. $69 (10% off single roll price)
- 10-Meter Roll (Click to Order) – Single-sided, 10-meter (Approx. 33 feet) x 1 inch wide roll – Enough tape to cover PT-3 & still have some tape left over for your pedal backs. $129 (15% off single roll price)
- Single Pedal Pack (Click to Order) – Two x 4 inch long x 1 inch wide strips. Enough tape for one standard sized pedal. $3.49
(Note: Make your selection above.)
POWER-GRIP is the best Solution for securing your guitar pedals to your pedalboard (No Hype).
Watch the video above and see the comparison for yourself.
INSTRUCTIONS FOR USE
- Mounting surfaces must be free of grease, dirt, loose particles, and moisture.
- Mounting surfaces must be smooth, even and stable.
- Metal surfaces should be cleaned with Acetone prior to mounting.
- Plastic & lacquered surfaces should be cleaned with Lighter Fluid prior to mounting.
- External temperature should be approximately 68° F (20°C) while applying Power-Grip.
- Cut two identically-sized strips of Power-Grip to the desired length.
- Fasten one strip to the object to be mounted and the other strip to the mounting surface.
- Press tape down firmly and evenly – use of a pressure roller is recommended.
- Use additional pairs of strips as needed for a stronger grip.
- For maximum adhesion, expose the adhesive to hot air (140°-180° F) for at least 2 minutes after mounting.
- Allow at least 24 hours for the Power-Grip adhesive to set.
- Press the two Power-Grip strips together and GRIP!
NOTES REGARDING USE
- The Power-Grip adhesive backing will form a permanent bond over time. Once this occurs, Power-Grip may damage painted surfaces or leave adhesive residue if removed. Residue can be removed with Acetone or Lighter Fluid.
- Power-Grip adheres best to smooth surfaces such as coated metal or plastic. It will not adhere well to very rough surfaces such as unfinished wood, etc.
- When in doubt, test adhesion to the surface FIRST using a small piece of Power-Grip.
- We do not guarantee that Power-Grip will be suitable for all applications and we do not take responsibility for loss or damage to property due to improper use/mounting of Power-Grip.
TEMPERATURE RANGE: -22° to +200° Fahrenheit (-30° to +93° Celsius)
ADHESIVE: Virtually weather & waterproof. Resistant to aging due to moisture & heat in accordance with Ford Spec. SKM-3G9512-A
DIMENSIONS: 25 mm (1 inch) wide, Approximately 5.4 mm (.2 inch) thick including backing adhesive
STEM COUNT: 42/CM2 (Approx. 100/ Inch2)
PEEL STRENGTH: Approx. 23 N/CM
SHEER STRENTH: Approx. 100 N/CM2
STORAGE: Dry, Dust-free, Dark area w/max. 75°F temp., 50% Humidity Level. 12-months maximum shelf life.